Grohe 43066000 Solenoid Valve - 1.7W - 12V DC

SUMMARY

GROHE 43066000 Solenoid Valve - 1.7W - 12V DC for Infrared Basin Taps

The GROHE 43066000 is a 12V DC 1.7W solenoid valve used in selected GROHE Allure E and Essence E infrared electronic basin taps and mixers. It is the electrically operated water-control valve within the tap assembly, rather than the infrared sensor, transformer or temperature-mixing mechanism.

The solenoid opens and closes the water supply in response to the tap's electronic controls. Replacing a defective valve can restore automatic water delivery or shut-off, but supply interruptions, blocked filters and disconnected electrical plugs should be checked before a non-operating tap is attributed to solenoid failure.

Technical Details

- - Part number: 43066000

- - Part type: electrically operated solenoid water-control valve

- - Operating voltage: 12V DC

- - Electrical connection: wired plug-in connection

- - Application: specified infrared electronic basin tap and mixer assemblies

- - Service drawing reference: 43 066

- - Associated solenoid filter reference: 42798000

Confirmed Models

- - GROHE 36095000 Allure E Infrared Electronic Basin Mixer Components

- - GROHE 36095000 GEN1 Allure E Infrared Electronic Basin Mixer Components - 2009 to 2016

- - GROHE 36096000 Allure E Infrared Electronic Basin Tap Components - without a mixing device

- - GROHE 36096000 GEN1 Allure E Infrared Electronic Basin Tap Components - 2009 to 2016

- - GROHE 36096 Allure E Basin Tap Components

- - GROHE 36097000 Allure E Infrared Electronic Basin Mixer Components - with mixing device, adjustable temperature limiter and waste set

- - GROHE 36088000 GEN1 Essence E Infrared Electronic Basin Mixer Components - 2009 to 2016

- - GROHE 36091000 Essence E Infrared Electronic Basin Mixer Components - with mixing device, adjustable temperature limiter and waste set

- - GROHE 36091 Essence E Infrared Electronic Basin Mixer Components

Before Ordering

Check the exact tap model, assembly version and existing solenoid part number. Compare the electrical connector and mounting arrangement before ordering; a matching voltage or similar appearance alone does not establish fitment. The 12V DC specification applies to this solenoid and should not be confused with the electrical specifications of the complete tap or its transformer.

Troubleshooting

Symptom: water continues to flow when the tap should have shut off. Likely Cause: a defective solenoid valve. Solution: have the valve checked and replace it if the fault is confirmed.

Symptom: no water flows when the tap is activated. Likely Cause: an interrupted water supply, blocked filter, disconnected plug, missing electrical supply or defective solenoid. Solution: check the supplies, connections and filter before replacing the valve.

Installation Notes

Isolate both the water and electrical supplies before servicing. Follow the instructions for the exact tap model, observe the solenoid's installation position and check the associated filter during the repair. After reassembly, check for leaks and confirm that the tap starts and stops the water flow correctly.

Related Spares You May Need

These are separate maintenance parts for the relevant tap assemblies above. The aerator and waste rods are not required for every solenoid repair, and the waste rods do not control water flow through the tap.

- - GROHE 13220000 Starlight Chrome Flow-Control Aerator - spout outlet component for the listed Allure E basin taps and mixers

- - GROHE 07052000 Horizontal Pop-Up Waste Rod - waste-linkage component for the waste-equipped 36097000 and 36091000 assemblies

- - GROHE 07341000 350mm Horizontal Pop-Up Waste Rod - optional waste-linkage part for the relevant waste-equipped installations; check the required rod length and waste arrangement

Help Identifying Your Part

For help before ordering, use the Di Vapor part identification service and provide photographs of the tap, existing valve, electrical connector and any visible model or part markings.

FAST DELIVERY

• Delivery of this item is priced as a 'small packet'. UK delivery costs £5.95 incl. VAT.
• For all in-stock spare parts the typical UK delivery timescale is 2-5 working days.
• If you need a part urgently then we can provide a next-day (delivered Mon-Fri) UK delivery service for all in-stock small parcels ordered before 3.00pm, Monday - Friday.
• Next day delivery is available to select at an additional charge during the checkout.
• We delivery WORLDWIDE. For more information about international deliveries, read our delivery page.

RETURNS

• If you need to return a part then please telephone Di Vapor on 0121 705 0866 with the reasons for the return within 14 days of receiving the goods.
• For more information please see our terms and conditions.